Valken 2-4 Cell Lipo/LiHV Smart Quick Charger (USA)



This product is currently unavailable for purchase.


View Full Details

The Valken 2-4 Cell LiPo/LiHV Quick  Charger is a plug and play balancing smart charger for lithium airsoft battery packs. The LiPo charger comes with its own power supply cable, and charges LiPo battery packs at 2A through 3-pin, 4-pin, or 5-pin charging ports. This lithium airsoft charger will safely charge lithium polymer airsoft batteries incredibly fast. . The LiPo charger also features reverse polarity and short circuit protection built in, as well as over-charge and over-current protection. 

Valken 2-4 Cell Lipo/LiHV Quick Smart Charger Safety Manual

Watch the 3 safety videos below if you are unfamiliar or new to charging airsoft batteries for safe and proper care, maintenance, and use of all type of airsoft battery packs and chargers.

Always charge your new battery fully before its first use.
Connect the DC power or AC adapter to the proper Lipo charger.
Plug the charger's power into an appropriate wall outlet.
To change battery charging modes between LiPo, LiFe, and LiHV press START/STOP button quickly and the red LED light will change from the LiPo mode to the LiFe mode to the LiHV mode.
Connect the battery pack to the charger with the small XH charging connector and make sure the polarity is connected in the right way.
Press and hold START/STOP button for 1-2 seconds or until the selected LED changes to green and begins to flash. Your battery is now charging.
Place battery inside a Lithium Battery Safety Bag while charging.
Battery pack is at full charge when green LED stops flashing.
Disconnect battery pack from charger before unplugging the charger from the wall outlet.

Never leave the charger unattended while it is connected to power supply.
Never attempt to charge more than 1 battery pack simultaneously from the same charger.
Only use the appropriate charger with your LiPo & Li-Ion batteries. Use of other chargers can result in fire, personal injury and property damage.
Never leave batteries and chargers unattended when in use. Always remove the battery from the charger or airsoft gun when not in use.
Always charge batteries in a safe area, on a stable non-flammable, heat-resistant, and non-conductive surface away from other flammable items. Unsafe charging surfaces include, but not limited to, car seats, carpet, bed, or something similar that can heat up quickly and melt or catch fire.
Never allow your battery and charger to be dislodged or fall during charging as this can result in fire, personal injury and property damage.
Never alter, modify or open your battery pack or charger.
Terminate charging immediately when any malfunction is observed.
Cancer and Reproductive Harm - 

Before charging complete a visual inspection of your battery and charger. At the sign of any damage or short circuit, do not use.
Never expose Li-Po & Li-Ion batteries to temperatures higher than 160 degrees F.
Never leave your Li-Po & Li-Ion battery in a closed vehicle.
Never use any charger accessory, such as wires extensions, adapters, or multi-connector adapters, that were not included with your charger from the factory. They may not be compatible with your charger and result in fire, property damage, or personal injury.
Any service or modification of any Li-Po & Li-Ion battery must be completed by a qualified dealer or original manufacturer.
Always keep your battery in a safe secure location to prevent damage during transport or storage.
Always keep batteries away from liquids.
Always keep batteries out of the reach of children.

Don't charge the following types of batteries:
Lead Acid battery or VRLA.
NiMh or NiCd battery packs.
Non-rechargeable battery (explosion hazard)
Faulty or damaged battery.
Battery pack which consists of different types of cells.
Any other type of battery except for Li-Po and Li-Ion battery packs.

  • For 7.4v - 14.8v LiPo / LiFe / LiHv
  • Charges battery packs from 200mAh to 3000mAh
  • Automatic constant current and constant voltage
  • Status LED
  • Reverse polarity and short-circuit protection
  • Over-charge and over-current protection
  • FCC, CE, and RoHS certified
  • Specifications
  • Compatibility: 7.4v-14.8v LiPo / LiFe / LiHV
  • Dimensions: 35mm x 60mm x 97mm
  • Connector Type: 3-pin, 4-pin, and 5-pin JST Connectors
  • Charge Rate: 2.0A
  • Input Voltage: 100-240v AC
  • Package Includes: Charger, and Manual
  • Videos

    Top of Page